Powerware 9315s User Manual Page 34
- Page / 205
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
2-- 6
Powerware 9315 Parallel Capacity/Redundant System with PHP SSBM
164201373 Rev. A 092402
2.8 Installing Optional SMB Wiring
NOTE: Refer to section 1.1.4 for additional guidance for wiring and conduit
installation.
NOTE: For SMB with100 kAIC short circuit rating, power rating must be secured as
shown in drawing 164201373 ---1.
Install power wiring to the SMB and between the SMB and critical load. Refer to
Appendix A of this manual for wiring and termination requirements and wiring access
information.
2.9 Preparing for Installing Optional Accessories
If you are installing optional accessories, such as a Remote Monitor Panel (RMP),
a Relay Interface Module (RIM), a Supervisory Contact Module (SCM),oraRemote
Emergency Power Off (EPO), you must install conduit between each device and the
UPS cabinet for wiring these options. Refer to Appendix A for the locations of the
interface points within the SSBM cabinet.
TopreparetheSSBMforwiringtoanRMP,RIM,SCM,orRemoteEPO:
1. Be sure the Parallel Capacity/Redundant system is turned off and all power
sources are removed. (See the operation section of this manual for shutdown
instructions.)
2. Remove the access plate on top of the SSBM control section to gain access to
the Customer Interface Panel (refer to Appendix A for location of the access
plate).
3. RefertoChapters3,4,5,or6asapplicableforinstallationinstructions.
2.10 Initial Startup
Startup and operational checks should be performed only by authorized service
personnel. Contact service in advance (usually a two week notice is required) to
reserve a preferred startup date.
2.11 Completing the Installation Checklist
The final step in installing your Parallel Capacity/Redundant system is completing
the following Installation Checklist. This checklist ensures that you have
completely installed all hardware, cables, and other equipment. Completing all
items listed on the checklist will ensure a smooth installation. You should make a
copy of the Installation Checklist before filling it out, and retain the original.
After your installation is complete, a service representative will be able to verify the
operation of your Parallel Capacity/Redundant system and commission it to
support your critical load. The service representative cannot perform any
installation tasks other than verifying software and operating setup parameters.
Service personnel may request a copy of the completed Installation Checklist to be
sure you have completed all applicable equipment installation.
NOTE: The Installation Checklist MUST be completed prior to starting the Parallel
Capacity/Redundant system for the first time.
- ,167$//$7,21 1
- 23(5$7,21 0$18$/ 1
- WARNING: 2
- Table of Contents 3
- Section II Operation 4
- List of Figures 9
- List of Figures (cont.) 10
- List of Tables 11
- Introduction 13
- Basic System Configurations 15
- Using This Manual 16
- Safety Considerations 18
- For More Information 19
- Getting Help 20
- Section I 21
- Installation 21
- Getting Started 23
- 1.1.2 Preparing Your Site 24
- Installing the Parallel 29
- 2.6 Installing UPM Cabinets 33
- 2.7 Installing SSBM Wiring 33
- 2.10 Initial Startup 34
- 2.12 Installation Checklist 35
- EMERGENCY OFF 37
- UNINTERRUPTIBLE POWER SYSTEM 37
- Installing a Remote 39
- Monitor Panel 39
- WIRES MUST 40
- BE TWISTED 40
- 4.2 To i ns tal l a n R M P: 41
- Installing a Relay 43
- Interface Module 43
- 5.2 To i ns tal l a RI M : 44
- Installing a Supervisory 47
- Contact Module 47
- 1. Securely mount the SCM 48
- Section II 51
- Operation 51
- Understanding Parallel 53
- 7.2.1 Normal Mode 56
- 7.2.2 Bypass Mode 57
- 7.2.3 Battery Mode 58
- 7.2.4 Load Bank Mode 59
- Path of Electrical Power 60
- Operational Cont rols 67
- CONTROL/MONITOR PANEL 68
- FRONT VIEW 68
- 110915520 69
- 8.3 Options and Accessories 73
- 8.4 Safety Considerations 74
- Using the Control Panel 77
- 9.2 Using the LCD Screen 78
- 9.3 Using the Pushbuttons 79
- 9.4 Adjusting the Contrast 79
- 9.6 Using the Menu Options 81
- 9.6.2 Load Amp Meters Screen 82
- Figure 9---5. Versions Screen 83
- 9.6.4 System History Screen 84
- 9.6.6 Unit Statistics Screen 86
- 9.6.7 Mimic Screen 87
- 9.6.8 T ime Setup Screen 88
- 9.6.9 Port Setup Screen 89
- 10.2 Operation of SSBM with 91
- 10.2.2 Manual Start 92
- 10.2.3 Auto Start 93
- 10.2.4 Single UPM Shutdown 94
- 10.3 Operation of SSBM with 98
- 10.3.2 Manual Start 99
- 10.3.3 Auto Start 100
- 10.3.4 Single UPM Shutdown 100
- 164201373 Rev. A 092402 101
- EMERGENCY UPM OFF 104
- Controls 106
- Using Features and Options 109
- 11.4 Remote Monitor Panel 110
- 11.5 Relay Interface Module 112
- 11.7 Common Battery Racks 114
- Responding to System Events 115
- 12.4 System Event Messages 116
- Serial Communications 123
- PORT 1 (DB--9) 124
- PORT 2 (DB--25) 125
- 13.4.1 Modes 127
- 13.4.2 Rate 127
- 13.4.3 Data/Stop 128
- 13.4.4 Handshaking 128
- 13.4.5 Save 128
- 13.4.6 Default Settings 128
- 13.5 Term i na l M od e 129
- 13.5.2 Entire Log (Ctrl + P) 130
- 13.6 System Configuration 132
- 13.6.5 Program Unit Name 135
- 13.6.6 Change Password 135
- 13.6.7 Battery Test Setup 136
- 13.7 Calibration Mode 137
- 13.8 Computer Mode 137
- 13.9 Remote Monitor Mode 137
- Remote Notification 139
- 14.3.2 Call Out 141
- 14.4 Hardware Requirements 142
- 14.5 Configuring the Modem 143
- 14.6 SSBM Setup Configuration 147
- 14.6.1 User Selected Events 148
- Maintaining the Parallel 151
- Capacity/Redundant System 151
- 15.4 Short Circuits 154
- 15.5 Circuit Breakers 154
- 15.6 Maintenance Training 154
- Product Specifications 155
- 16.3 SSBM Output 156
- INSTALLATION NOTES 159
- 164201373---1 159
- DESCRIPTION: 160
- DRAWING NO: 160
- ¦10˚during handling 162
- SEPARATE BATTERY SYSTEM 164
- COMMON BATTERY SYSTEM 165
- SEPARATE BATTERY PARALLEL 166
- CAPACITY/REDUNDANT 166
- See Sheet 3 for notes 166
- COMMON BATTERY PARALLEL 167
- Customer Interface Panel 169
- To p V i e w 169
- TYPICAL POWERNET NETWORK 170
- WIRING AND TERMINATIONS 170
- Terminating Resistor Location 171
- DRAWING NO: SHEET: 172
- UPM PowerNet Interface Panel 175
- 164201373---5 176
- UPM POWERNET INTERFACE PANEL: 176
- A --- 2 0 176
- A --- 2 1 177
- A --- 2 3 179
- UPM CAN INTERFACE: 179
- POWERWARE 9315--625/750 UPMs 179
- 164201373---6 179
- CUSTOMER INTERFACE 180
- A --- 3 2 188
- 164201373---11 188
- PowerHandlerPlus SSBM 188
- A --- 3 3 189
- A --- 3 4 190
- Floor Mounting Details 191
- A --- 3 6 192
- 164201373---12 192
- A --- 3 7 193
- A --- 3 8 194
- A --- 4 0 196
- 164201373---13 196
- TYPICAL SSBM CONTROL SECTION 196
- A --- 4 1 197
- A --- 4 2 198
- A --- 4 3 199
- CONDUIT CONFIGURATIONS 200
- A --- 4 4 200
- 164201373---14 200
- UPM OUTPUT-TO-SSBM CABLE AND 200
- A --- 4 5 201
- A --- 4 6 202
- 205
Related products and manuals for Uninterruptible power supplies (UPSs) Powerware 9315s
(58 pages)
(52 pages)© 2020, manymanuals.com. All rights reserved. | 1.294 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals