Powerware 9315s User Manual Page 23
- Page / 205
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
1-- 1
Powerware 9315 Parallel Capacity/Redundant System with PHP SSBM
164201373 Rev. A 092402
n
Getting Started
1.1 Installing the UPS
The Switchboard System Bypass Module (SSBM) and UPMs of the Parallel
Capacity/Redundant system are shipped on separate pallets. Use a forklift or pallet
jack to move the packaged cabinets to the installation site, o r as close as possible
to the site, before unloading from the pallet.
This is the basic sequence of the installation steps:
1. Create an installation plan for the Parallel Capacity/Redundant system
(Chapter 1).
2. Prepare your site for the Parallel Capacity/Redundant system (Chapter 1).
3. Inspect, unpack, and unload the SSBM (Chapter 1).
4. Inspect, unpack, and unload the UPMs (refer to the applicable Powerware
9315 Installation manual provided with the UPM).
5. Wire the system (refer to Chapter 2 and the applicable Powerware 9315
Installation manual provided with the UPM).
6. Install features, accessories, and/or options, as applicable (Chapter 3).
7. Complete the Installation Checklist (Chapter 2).
8. Have authorized service personnel perform preliminary operational checks and
startup.
NOTE: Startup and operational checks should be performed only by authorized
service personnel. This service is usually offered as part of the sales
contract for your Parallel Capacity/Redundant system.Contactservicein
advance (usually a two week notice is required) to reserve a preferred
startup date.
1.1.1 Creating an Installation Plan
Before beginning to install the Parallel Capacity/Redundant system, read and
understand how this manual applies to the system being installed. Use the
procedures and illustrations in the following chapters to create a logical plan for
installing the system. It is important to note that UPM installation procedures are
contained in the applicable Powerware 9315 Installation manual provided with the
UPMs. First understand how to install the UPMs before installing the S SBM. The
information in Chapter 2 of this manual provides a guide to installation of the SSBM
to the UPMs.
1
- ,167$//$7,21 1
- 23(5$7,21 0$18$/ 1
- WARNING: 2
- Table of Contents 3
- Section II Operation 4
- List of Figures 9
- List of Figures (cont.) 10
- List of Tables 11
- Introduction 13
- Basic System Configurations 15
- Using This Manual 16
- Safety Considerations 18
- For More Information 19
- Getting Help 20
- Section I 21
- Installation 21
- Getting Started 23
- 1.1.2 Preparing Your Site 24
- Installing the Parallel 29
- 2.6 Installing UPM Cabinets 33
- 2.7 Installing SSBM Wiring 33
- 2.10 Initial Startup 34
- 2.12 Installation Checklist 35
- EMERGENCY OFF 37
- UNINTERRUPTIBLE POWER SYSTEM 37
- Installing a Remote 39
- Monitor Panel 39
- WIRES MUST 40
- BE TWISTED 40
- 4.2 To i ns tal l a n R M P: 41
- Installing a Relay 43
- Interface Module 43
- 5.2 To i ns tal l a RI M : 44
- Installing a Supervisory 47
- Contact Module 47
- 1. Securely mount the SCM 48
- Section II 51
- Operation 51
- Understanding Parallel 53
- 7.2.1 Normal Mode 56
- 7.2.2 Bypass Mode 57
- 7.2.3 Battery Mode 58
- 7.2.4 Load Bank Mode 59
- Path of Electrical Power 60
- Operational Cont rols 67
- CONTROL/MONITOR PANEL 68
- FRONT VIEW 68
- 110915520 69
- 8.3 Options and Accessories 73
- 8.4 Safety Considerations 74
- Using the Control Panel 77
- 9.2 Using the LCD Screen 78
- 9.3 Using the Pushbuttons 79
- 9.4 Adjusting the Contrast 79
- 9.6 Using the Menu Options 81
- 9.6.2 Load Amp Meters Screen 82
- Figure 9---5. Versions Screen 83
- 9.6.4 System History Screen 84
- 9.6.6 Unit Statistics Screen 86
- 9.6.7 Mimic Screen 87
- 9.6.8 T ime Setup Screen 88
- 9.6.9 Port Setup Screen 89
- 10.2 Operation of SSBM with 91
- 10.2.2 Manual Start 92
- 10.2.3 Auto Start 93
- 10.2.4 Single UPM Shutdown 94
- 10.3 Operation of SSBM with 98
- 10.3.2 Manual Start 99
- 10.3.3 Auto Start 100
- 10.3.4 Single UPM Shutdown 100
- 164201373 Rev. A 092402 101
- EMERGENCY UPM OFF 104
- Controls 106
- Using Features and Options 109
- 11.4 Remote Monitor Panel 110
- 11.5 Relay Interface Module 112
- 11.7 Common Battery Racks 114
- Responding to System Events 115
- 12.4 System Event Messages 116
- Serial Communications 123
- PORT 1 (DB--9) 124
- PORT 2 (DB--25) 125
- 13.4.1 Modes 127
- 13.4.2 Rate 127
- 13.4.3 Data/Stop 128
- 13.4.4 Handshaking 128
- 13.4.5 Save 128
- 13.4.6 Default Settings 128
- 13.5 Term i na l M od e 129
- 13.5.2 Entire Log (Ctrl + P) 130
- 13.6 System Configuration 132
- 13.6.5 Program Unit Name 135
- 13.6.6 Change Password 135
- 13.6.7 Battery Test Setup 136
- 13.7 Calibration Mode 137
- 13.8 Computer Mode 137
- 13.9 Remote Monitor Mode 137
- Remote Notification 139
- 14.3.2 Call Out 141
- 14.4 Hardware Requirements 142
- 14.5 Configuring the Modem 143
- 14.6 SSBM Setup Configuration 147
- 14.6.1 User Selected Events 148
- Maintaining the Parallel 151
- Capacity/Redundant System 151
- 15.4 Short Circuits 154
- 15.5 Circuit Breakers 154
- 15.6 Maintenance Training 154
- Product Specifications 155
- 16.3 SSBM Output 156
- INSTALLATION NOTES 159
- 164201373---1 159
- DESCRIPTION: 160
- DRAWING NO: 160
- ¦10˚during handling 162
- SEPARATE BATTERY SYSTEM 164
- COMMON BATTERY SYSTEM 165
- SEPARATE BATTERY PARALLEL 166
- CAPACITY/REDUNDANT 166
- See Sheet 3 for notes 166
- COMMON BATTERY PARALLEL 167
- Customer Interface Panel 169
- To p V i e w 169
- TYPICAL POWERNET NETWORK 170
- WIRING AND TERMINATIONS 170
- Terminating Resistor Location 171
- DRAWING NO: SHEET: 172
- UPM PowerNet Interface Panel 175
- 164201373---5 176
- UPM POWERNET INTERFACE PANEL: 176
- A --- 2 0 176
- A --- 2 1 177
- A --- 2 3 179
- UPM CAN INTERFACE: 179
- POWERWARE 9315--625/750 UPMs 179
- 164201373---6 179
- CUSTOMER INTERFACE 180
- A --- 3 2 188
- 164201373---11 188
- PowerHandlerPlus SSBM 188
- A --- 3 3 189
- A --- 3 4 190
- Floor Mounting Details 191
- A --- 3 6 192
- 164201373---12 192
- A --- 3 7 193
- A --- 3 8 194
- A --- 4 0 196
- 164201373---13 196
- TYPICAL SSBM CONTROL SECTION 196
- A --- 4 1 197
- A --- 4 2 198
- A --- 4 3 199
- CONDUIT CONFIGURATIONS 200
- A --- 4 4 200
- 164201373---14 200
- UPM OUTPUT-TO-SSBM CABLE AND 200
- A --- 4 5 201
- A --- 4 6 202
- 205
Related products and manuals for Uninterruptible power supplies (UPSs) Powerware 9315s
(58 pages)
(52 pages)© 2020, manymanuals.com. All rights reserved. | 0.292 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals