Powerware 9315s User Manual Page 128
- Page / 205
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
13--6
Powerware 9315 Parallel Capacity/Redundant System with PHP SSBM
164201373 Rev. A 092402
13.4.3 Data/Stop
The data size and stop bits of the equipment connected to this port. These
settings determine the number of bits transmitted per ASCII character. The data
size and stop bits you specify depend on the configuration of your equipment.
For Port 1, the data size must be set to 8, with 1 or 2 stop bits. Settings of 7 data
bits/1 stop bit and 7 data bits/2 stop bits are available for Port 2.
NOTE: When connecting a computer running a terminal emulation program, you
should set your equipment to NO PARITY.
13.4.4 Handshaking
This setting controls handshaking. You can select XON/XOFF or Disabled for this
setting.
D Disabled (No Handshaking)
If handshaking is disabled, the SSBM transmits and receives data via the serial
port, ignoring all inputs from handshaking lines.
D XON/XOFF
If handshaking is enabled, the SSBM uses special characters (XON and XOFF) to
handshake with the host terminal. The XON character is defined to be ASCII value
11 hex, and the XOFF character is defined to be ASCII value 13 hex. Upon
reception of an XOFF command, the SSBM halts transmission until an XON
command is received. In the same way, if the terminal receives an XOFF
command, the SSBM expects the terminal to halt transmission until the SSBM
sends an XON command.
13.4.5 Save
Set to YES to save any changes to configuration settings upon exit from the Setup
screen. Set to NO if you do not want to save any changes.
13.4.6 Default Settings
The following are the default configuration settings for the serial communications
ports:
Port 1 Remote Monitor 300 baud 8/1 Handshaking Disabled
Port 2 Terminal 9600 baud 8/1 Handshaking Disabled
Each communications port on the SSBM operates in one of five modes which you
select when configuring the port using the Setup Port screen.
- ,167$//$7,21 1
- 23(5$7,21 0$18$/ 1
- WARNING: 2
- Table of Contents 3
- Section II Operation 4
- List of Figures 9
- List of Figures (cont.) 10
- List of Tables 11
- Introduction 13
- Basic System Configurations 15
- Using This Manual 16
- Safety Considerations 18
- For More Information 19
- Getting Help 20
- Section I 21
- Installation 21
- Getting Started 23
- 1.1.2 Preparing Your Site 24
- Installing the Parallel 29
- 2.6 Installing UPM Cabinets 33
- 2.7 Installing SSBM Wiring 33
- 2.10 Initial Startup 34
- 2.12 Installation Checklist 35
- EMERGENCY OFF 37
- UNINTERRUPTIBLE POWER SYSTEM 37
- Installing a Remote 39
- Monitor Panel 39
- WIRES MUST 40
- BE TWISTED 40
- 4.2 To i ns tal l a n R M P: 41
- Installing a Relay 43
- Interface Module 43
- 5.2 To i ns tal l a RI M : 44
- Installing a Supervisory 47
- Contact Module 47
- 1. Securely mount the SCM 48
- Section II 51
- Operation 51
- Understanding Parallel 53
- 7.2.1 Normal Mode 56
- 7.2.2 Bypass Mode 57
- 7.2.3 Battery Mode 58
- 7.2.4 Load Bank Mode 59
- Path of Electrical Power 60
- Operational Cont rols 67
- CONTROL/MONITOR PANEL 68
- FRONT VIEW 68
- 110915520 69
- 8.3 Options and Accessories 73
- 8.4 Safety Considerations 74
- Using the Control Panel 77
- 9.2 Using the LCD Screen 78
- 9.3 Using the Pushbuttons 79
- 9.4 Adjusting the Contrast 79
- 9.6 Using the Menu Options 81
- 9.6.2 Load Amp Meters Screen 82
- Figure 9---5. Versions Screen 83
- 9.6.4 System History Screen 84
- 9.6.6 Unit Statistics Screen 86
- 9.6.7 Mimic Screen 87
- 9.6.8 T ime Setup Screen 88
- 9.6.9 Port Setup Screen 89
- 10.2 Operation of SSBM with 91
- 10.2.2 Manual Start 92
- 10.2.3 Auto Start 93
- 10.2.4 Single UPM Shutdown 94
- 10.3 Operation of SSBM with 98
- 10.3.2 Manual Start 99
- 10.3.3 Auto Start 100
- 10.3.4 Single UPM Shutdown 100
- 164201373 Rev. A 092402 101
- EMERGENCY UPM OFF 104
- Controls 106
- Using Features and Options 109
- 11.4 Remote Monitor Panel 110
- 11.5 Relay Interface Module 112
- 11.7 Common Battery Racks 114
- Responding to System Events 115
- 12.4 System Event Messages 116
- Serial Communications 123
- PORT 1 (DB--9) 124
- PORT 2 (DB--25) 125
- 13.4.1 Modes 127
- 13.4.2 Rate 127
- 13.4.3 Data/Stop 128
- 13.4.4 Handshaking 128
- 13.4.5 Save 128
- 13.4.6 Default Settings 128
- 13.5 Term i na l M od e 129
- 13.5.2 Entire Log (Ctrl + P) 130
- 13.6 System Configuration 132
- 13.6.5 Program Unit Name 135
- 13.6.6 Change Password 135
- 13.6.7 Battery Test Setup 136
- 13.7 Calibration Mode 137
- 13.8 Computer Mode 137
- 13.9 Remote Monitor Mode 137
- Remote Notification 139
- 14.3.2 Call Out 141
- 14.4 Hardware Requirements 142
- 14.5 Configuring the Modem 143
- 14.6 SSBM Setup Configuration 147
- 14.6.1 User Selected Events 148
- Maintaining the Parallel 151
- Capacity/Redundant System 151
- 15.4 Short Circuits 154
- 15.5 Circuit Breakers 154
- 15.6 Maintenance Training 154
- Product Specifications 155
- 16.3 SSBM Output 156
- INSTALLATION NOTES 159
- 164201373---1 159
- DESCRIPTION: 160
- DRAWING NO: 160
- ¦10˚during handling 162
- SEPARATE BATTERY SYSTEM 164
- COMMON BATTERY SYSTEM 165
- SEPARATE BATTERY PARALLEL 166
- CAPACITY/REDUNDANT 166
- See Sheet 3 for notes 166
- COMMON BATTERY PARALLEL 167
- Customer Interface Panel 169
- To p V i e w 169
- TYPICAL POWERNET NETWORK 170
- WIRING AND TERMINATIONS 170
- Terminating Resistor Location 171
- DRAWING NO: SHEET: 172
- UPM PowerNet Interface Panel 175
- 164201373---5 176
- UPM POWERNET INTERFACE PANEL: 176
- A --- 2 0 176
- A --- 2 1 177
- A --- 2 3 179
- UPM CAN INTERFACE: 179
- POWERWARE 9315--625/750 UPMs 179
- 164201373---6 179
- CUSTOMER INTERFACE 180
- A --- 3 2 188
- 164201373---11 188
- PowerHandlerPlus SSBM 188
- A --- 3 3 189
- A --- 3 4 190
- Floor Mounting Details 191
- A --- 3 6 192
- 164201373---12 192
- A --- 3 7 193
- A --- 3 8 194
- A --- 4 0 196
- 164201373---13 196
- TYPICAL SSBM CONTROL SECTION 196
- A --- 4 1 197
- A --- 4 2 198
- A --- 4 3 199
- CONDUIT CONFIGURATIONS 200
- A --- 4 4 200
- 164201373---14 200
- UPM OUTPUT-TO-SSBM CABLE AND 200
- A --- 4 5 201
- A --- 4 6 202
- 205
Related products and manuals for Uninterruptible power supplies (UPSs) Powerware 9315s
(58 pages)
(52 pages)© 2020, manymanuals.com. All rights reserved. | 0.085 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals