Powerware 9335 User Manual Page 20
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
2-2 Powerware 9335 (80 kVA and 120 kVA) Installation and Operation
164201396 REV A 071103
2.2 UPS Cabinet Installation
To install an UPS cabinet, perform the procedures in the following paragraphs.
2.2.1 Unloading the Powerware 9335 (80 kVA and 120 kVA) UPS
Cabinet from the Pallet
The UPS cabinet is bolted to a wooden shipping base using two steel angles. To remove
the shipping material, perform the following procedure.
1. Remove accessory installation kit located at the top of the unit (see figure 1.1) by
opening top of outer box.
Remove the 4 jacking bolts from the accessory pack.
Use a forklift or other material handling equipment to move the cabinet to the
installation area. Insert the forklift forks under the unit and keep the unit elevated
approximately 3 inches above the ground.
2.
Remove
the outer stretch wrapping. The two steel angles which connect the UPS
cabinet to the wooden shipping base contain 2 threaded holes for inserting jacking
bolts..
3.
Unbolt the wooden cross members on the shipping base by removing the four nuts
(10 mm) which fasten the wooden pallet to the steel brackets. Remove the wooden
cross members from the steel brackets. Insert the jacking bolts into the holes and
lower them to the ground, in order for the weight of the unit to be supported by the 4
bolts. Place small metal plates under the jacking bolts to prevent floor damage.
Ensure the unit does not tilt more than specified in the caution note above. Remove
the forklift or pallet jack once the unit is supported on the jacking bolts. Slowly lower
the UPS by alternating between the four jacking bolts, until the steel brackets are on
the floor. Remove the jacking bolts. Detach the UPS cabinet from the angle steel by
removing all of the M5 Phillips-head machine screws that fasten them, using a #3
Phillips head screwdriver. Tilt the unit slightly to enable the steel bracket to be
removed from beneath two legs. Lower the unit down to the floor.
4.
Repeat the process for the other side by tilting the unit and removing the steel bracket.
(See illustrated procedure packed on the outside of the shipping carton.)
5.
The UPS cabinet may now be moved to its final position for installation.
WARNING:
The UPS cabinet is heavy. Refer to Table J in Appendix A for weight of
cabinets. If unloading instructions are not closely followed, the cabinet may
cause serious in
j
ur
y
.
CAUTION:
Do not tilt cabinets more than ±10 degrees from vertical. Do not cut the
outside protective cardboard packing box open. Damage to the enclosed
cabinet ma
y
occur.
CAUTION:
Carefully open top of outer package and remove accessory installation kit
before removin
g
outer
p
acka
g
in
g
. A
pp
roximate wei
g
ht is 25 lbs.
(
11 k
g
.
)
- Table of Contents 4
- Section II Operation 5
- 164201396 REV. A 071103 10
- 164201396 REV. A 071103 11
- Safety Considerations 12
- Getting Help 12
- Section I 13
- Installation 13
- Getting Started 15
- 1.1.2 Preparing Your Site 16
- 164201396 REV A 071103 17
- Cabinet from the Pallet 20
- 2.4 Initial Startup 23
- Installation Checklist 24
- EMERGENCY OFF 27
- X1 UPS 28
- TWISTED 28
- WIRES (2) 28
- Section II 29
- Operation 29
- 164201396 REV A 071103 30
- Understanding UPS Operation 31
- 164201396 REV. A 071103 33
- 5.2.1 Normal Mode 34
- 5.2.2 Bypass Mode 36
- 5.2.3 Battery Mode 38
- Maintenance Bypass Mode 40
- 5.3.5 Static Bypass 42
- 5.3.6 Maintenance Bypass 42
- 6.1 General 43
- 6.2.1 Control Panel 44
- 6.3 UPS Standard Features 45
- 6.4 Options and Accessories 46
- 6.5 Safety Considerations 47
- the Control Panel 49
- 7.2 Using the Control Panel 50
- 7.2.3 Pushbutton Functions 51
- 7.3.1 Status Screens 52
- • HH-MM-SS 53
- PERFORM 53
- 7.3.3 Main Menu Screen 54
- 7.3.4 Event Log Screen 54
- 7.3.5 Measurements Screen 54
- SET-UP USER 54
- SET-UP SERVICE 54
- 7.3.6 Commands Screen 55
- 7.3.7 UPS Data 56
- 7.3.8 Set-Up User 56
- 7.3.9 Set-Up Service 57
- 7.4 O perating Modes 58
- Instructions 61
- 9.1 Alarms 67
- Communications 69
- Control Panel 70
- 11.1 Generator ON Facility 73
- 12.1 General 75
- 13.3 UPS System Output 78
- 164201396 REV A 07/11/2003 79
- Powerware 9335 – 80 kVA 80
- Powerware 9335 – 120 kVA 81
- During Full Load Operation 87
- 164201396 REV A. 071103 100
Related products and manuals for Tools Powerware 9335
Tools Powerware BladeUPS none User Manual
(32 pages)
(32 pages)
Tools Powerware 5140 User Manual
(68 pages)
(68 pages)
Tools Powerware 9 User Manual
(70 pages)
(70 pages)
Tools Powerware 9170+ User Manual
(12 pages)
(12 pages)
Tools Powerware 9170+ User Manual
(94 pages)
(94 pages)
Tools Powerware 9155 UPS20-30kVA User Manual
(52 pages)
(52 pages)
Tools Powerware 9330 User Manual
(246 pages)
(246 pages)
Tools Powerware 5110 User Manual
(14 pages)
(14 pages)
Tools Powerware 5105 User Manual
(4 pages)
(4 pages)
Tools Powerware UPS 1000 - 2200 User Manual
(24 pages)
(24 pages)
Tools Powerware 5075 kVA User Manual
(162 pages)
(162 pages)
Tools Powerware 9125 User Manual
(30 pages)
(30 pages)
Tools Powerware 9150 User Manual
(64 pages)
(64 pages)
Tools Powerware 9120 User Manual
(24 pages)
(24 pages)
Tools Powerware 9155 User Manual
(10 pages)
(10 pages)
© 2020, manymanuals.com. All rights reserved. | 0.267 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals