Powerware 9315 User Manual Page 81
- Page / 154
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
USING FEATURES AND OPTIONS
EATON Powerware
®
9315 UPS (500–750 kVA) Installation and Operation Manual S 164201244 Rev E www.powerware.com
10-3
The RMP contains a local horn and the following backlit status indicators:
SYSTEM NORMAL
The UPS is energized (either with utility power or battery backup) and is
supplying conditioned power to the critical load.
NO REDUNDANCY
This indicator applies only to parallel systems when one cabinet is not
functioning. This feature is not available on this system.
ON GENERATOR
This alarm means that the UPS input and bypass are being supplied by the
power from the generator, instead of from the utility power.
ON BYPASS
The bypass source is supplying the critical load. Usually this means that
the UPS is not energized. The load is not protected in Bypass mode, and a
horn sounds after 30 seconds.
UPS ALARM
The UPS system is issuing an alarm. Conditions that affect the current UPS
mode are indicated by the indicators and horn on the UPS.
ON BATTERY
The UPS battery backup is supplying the critical load. The utility power is
either interrupted or out of specification. The SYSTEM NORMAL indicator
is also lit.
BYPASS UNAVAILABLE
The UPS system is in Normal mode, but a bypass source is not within
specification. A horn sounds after 30 seconds.
SHUTDOWN IMMINENT
The UPS is preparing to shut down because the UPS is in Battery mode
and the DC voltage is approaching its low limit.
This indicator is accompanied by a horn.
- Powerware 9315 UPS 1
- 500–750 kVA 1
- CONSERVER CES INSTRUCTIONS 2
- Special Symbols 3
- Table of Contents 5
- TABLE OF CONTENTS 6
- List of Figures 9
- LIST OF FIGURES 10
- Chapter 1 Introduction 11
- 1.1 UPS Features 12
- 1.2 Options and Accessories 13
- INTRODUCTION 14
- IMPORTANT SAFETY INSTRUCTIONS 15
- SAVE THESE INSTRUCTIONS 15
- A V E R T I S S E M E N T ! 16
- A T T E N T I O N ! 16
- 1.6 For More Information 16
- 1.7 Getting Help 17
- Section I 19
- Installation 19
- 2.1.1 Preparing Your Site 21
- A N G E R 25
- A R N I N G 26
- INSTALLING THE UPS SYSTEM 27
- 3.4 Multi‐Module Installation 28
- 3.7 Installing Accessories 30
- 3.8 Initial Startup 30
- Installation Checklist 32
- Operating Handle 35
- ON Position 35
- OFF Position 35
- 5.1 REPO Installation 37
- 5.2 REPO Operation 38
- S X-Slot cards 39
- 6.1 Installing an RMP 40
- 6.2 Installing an RIM 43
- 6.3 Installing an SCM 45
- Figure 6‐7. SCM TB2 47
- 6.4 Installing X-Slot Cards 48
- Section II 49
- Operation 49
- Battery String 51
- Module Bypass Cabinet (MBC) 51
- Processing Unit 51
- 7.1 Operating Modes 52
- 7.1.1 Normal Mode 53
- 7.1.3 Battery Mode 55
- UNDERSTANDING UPS OPERATION 56
- Figure 8‐1. UPS Control Panel 57
- 8.1 Using the LCD Screen 58
- 8.2 Using the Pushbuttons 59
- 8.3 Adjusting the Contrast 59
- 8.5 Using the Menu Options 60
- 8.5.1 System Meters Screen 61
- 8.5.2 Load Amps Meters Screen 62
- 8.5.6 Unit Statistics Screen 66
- 8.5.7 Mimic Screen 67
- 8.5.8 Time Setup Screen 68
- 8.5.9 Port Setup Screen 69
- USING THE CONTROL PANEL 70
- 9.1.3 Emergency UPM Off 72
- 9.1.1 Control Panel 72
- 9.1.2 UPS Circuit Breakers 72
- 9.2 Starting the UPS 73
- UPS Input Breaker (CB1) OPEN 74
- UPS Output Breaker (CB3) OPEN 74
- UPS Bypass Breaker (CB4) OPEN 74
- UPS OPERATING INSTRUCTIONS 78
- Figure 10‐1. RMP 80
- USING FEATURES AND OPTIONS 81
- Figure 10‐2. RIM 82
- Figure 10‐3. SCM 83
- 11.1 System Event Horns 85
- 11.2 System Event Indicators 85
- 11.3 System Event Messages 85
- RESPONDING TO SYSTEM EVENTS 86
- Chapter 12 Communication 87
- Figure 12‐2. Port 2 (DB‐25) 88
- 12.3.1 Modes 90
- 12.3.2 Rate 90
- 12.3.3 Data/Stop 91
- 12.3.4 Handshaking 91
- 12.3.5 Save 91
- 12.3.6 Default Settings 91
- 12.4 Terminal Mode 92
- 12.4.2 Entire Log [Ctrl]+[P] 93
- COMMUNICATION 94
- 12.5.5 Program Unit Name 97
- 12.5.6 Change Password 97
- 12.5.7 Battery Test Setup 98
- 12.6 Calibration Mode 99
- 12.7 Computer Mode 99
- 12.8 Remote Monitor Mode 99
- 12.9 eNotify Service 100
- 12.10 Remote Notification 101
- 12.11 X-Slot Cards 102
- D A N G E R 103
- W A R N I N G 103
- 13.2.2 Monthly Maintenance 104
- 13.2.3 Annual Maintenance 104
- 13.2.1 Daily Maintenance 104
- C A U T I O N 105
- 13.4 Maintenance Training 105
- MAINTAINING THE UPS SYSTEM 106
- 14.1 Model Numbers 107
- 14.2 UPS System Input 107
- 14.3 UPS System Output 108
- Chapter 15 Warranty 109
- WARRANTY 110
- Appendix A 111
- Installation Reference 111
- INSTALLATION REFERENCE 112
- FRONT VIEW 113
- TOP VIEW 114
- LEFT VIEW 114
- CUSTOMER 120
- INTERFACE 120
- Figure A‐10. Securing Cables 128
- A.4 Location of UPS Terminals 132
- LEFT SIDE 133
- LEFT SIDE FRONT 136
- MBC – TOP AND BUS BARS 137
- Battery Terminal Board 139
- Battery I/O Board 139
- X-SLOT CARD 140
- CUSTOMER INTERFACE 141
- PANEL (X-SLOT) 141
- EATON Powerware 143
- A.6 Typical REPO 146
- Front View 147
- *164201244E* 154
Related products and manuals for Hardware Powerware 9315
Hardware Powerware 5115 User Manual
(2 pages)
(2 pages)
Hardware Powerware 9315 User Manual
(54 pages)
(54 pages)
© 2020, manymanuals.com. All rights reserved. | 0.406 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals